- Ultra-compact embedded system-on-modules
- 10/100 Ethernet interface
- RJ-45 form factor
- Compatible with Digi Connect Wi-ME®
- Supports Digi Embedded Linux and NET+OS
- Digi Part No: DC-ME-Y402-C
FEATURES
Get your inquiry
Product: Digi Connect ME® 9210
SKU:
Request callback
Product: Digi Connect ME® 9210
SKU:
Description
Digi Connect ME® 9210 for NET+OS: Powerful embedded system-on-module with extended memory
The Digi Connect ME® 9210 defines new standards for powerful and flexible embedded systems with its focus on extended memory. With an impressive 4 MB Flash and 8 MB RAM, this SoM provides a robust platform for network-enabled applications with extensive memory requirements.
The plug-and-play firmware enables seamless integration and easy configuration, minimizing development time and maximizing the efficiency of the product development process.
The Digi Connect ME® 9210 UPW complies with SB-327 standards, ensuring high interoperability and compatibility with other devices and systems.
Versatile application possibilities
This embedded system-on-module is particularly well suited for applications that require extended storage capacity, whether in data processing, application data storage or handling complex network requirements.
Experience the power of the Digi Connect ME® 9210 UPW and benefit from its expanded memory, plug-and-play firmware and SB-327 compliance for smooth integration into your network-enabled applications.
Digi Part No.: DC-ME-Y402-C
Specifications
Digi Connect ME® 9210 | |
---|---|
GENERAL | |
Prozessort type | 32-bit Digi NS9210 processor |
ARM Core | ARM926EJ-S |
Processor speed | 75 MHz |
Cache | 4k I/D-Cache |
Memory Base / Population | 2/4 MB NOR flash 8 MB SDRAM |
Flexible Interface Modules(FIMs) | 300 MHz DRPIC165X CPU 2k program/192 bytes data RAM |
On-Chip 256-Bit-AES Accelerator | Yes |
Power Management Modes | On-the-fly clock scaling Low-power sleep modes Configurable scaling/wake-up events (EIRQ, UART, Ethernet, etc.) |
Pins/Form Factor | RJ-45 connector style with 20-pin micro pin header (Samtec FTS-110-01-F-DV-TR) |
High-Speed TTL Serial Interface | Full signal support (TXD, RXD, RTS, CTS, DTR, DSR and DCD) Hardware/Software flow control |
GPIO | 10 shared Up to 3 external IRQ options |
SPI | Master data rate up to 16.7 Mbps Slave data rate up to 7.5 Mbps |
I2C | v1.0 bus interface 7-bit and 10-bit address modes |
Flexible Interface Support (FIM) | UART, 1-Wire, CAN |
Watchdog-Timer (16-Bit) | Yes |
JTAG Interface | Available on development modules only (P/N DC-ME-Y401-JT, DC-ME-Y402-[LX]-JT) |
On-Board Power Supervisor | Yes |
Wave-Solderable Design | No clean flux process |
Dimensions (L x W x H) | 1.445 in (36.7 mm) x 0.75 in (19.05 mm) x 0.735 in (18.67 mm) |
NETWORK INTERFACE – WIRED | |
Physical layer | 10/100Base-T |
Data rate | 10/100 Mbps (auto-sensing) |
Mode | Full- or half-duplex (auto-sensing) |
Connector | RJ-45 w/ magnetics |
PoE Power Pass-Through | 802.3af compliant (Mid- and End-span) |
ENVIRONMENTAL | |
Operating temperature | -40° C to +80° C (-40° F to +176° F) |
Storage temperature | -50° C to +125° C (-58° F to +257° F) |
Relative humidity | 5% to 90% (non-condensing) |
POWER REQUIREMENTS (3.3 VDC) | |
Maximum | 450 mA (1.485 W) |
Typical | 346 mA (1.14 W) UART and Ethernet activated |
Idle | 186 mA (613 mW) /16 clock scaling, Ethernet activated |
Sleep | 34 mA (113 mW) Wake-up on EIRQ, Ethernet PHY off |
REGULATORY APPROVALS | |
FCC Part 15 Class B, EN 55022 Class B | Yes |
EN 61000-3-2 and EN 61000-3-3 | Yes |
ICES-003 Class B, VCCI Class II, AS 3548 | Yes |
FCC Part 15 Sub C Section 15.247 | Yes |
IC RSS-210 Issue 5 Section 6.2.2(o) | Yes |
EN 300 328, EN 301 489-17 | Yes |
UL 60950-1, EN 60950 (EU) | Yes |
CSA C22.2, Nr. 60950 | Yes |
EN 55024 | Yes |
WARRANTY | |
Product warranty | 3-years |
Documents
Digi Connect ME 9210 Datasheet | |
Digi ConnectCore Embedded Feature – Product Comparison Guide (SOMs & SBCs) |
Order information
Order information | Digi Connect ME® 9210 series |
---|---|
DIGI JUMPSTART KITS | |
DC-ME-9210-LX | Digi Connect ME 9210 Digi JumpStart Kit for Digi Embedded Linux, w/Eclipse-based Digi ESP IDE, LiveDVD, and installation and setup support package |
DC-ME-9210-NET | Digi Connect ME 9210 Digi JumpStart Kit for NET+OS 7 w/Eclipse-based Digi ESP IDE, USB debugger, installation and setup support package |
MODULES FOR DIGI-PLUG-AND-PLAY FIRMWARE | |
DC-ME-Y402-S-UPW | Digi Connect ME 9210 w/4 MB Flash, 8 MB RAM, Plug-and-Play Firmware, SB-327 compliant |
MODULES FOR LINUX | |
DC-ME-Y402-LX | Digi Connect ME 9210 w/4 MB Flash, 8 MB RAM (single-unit pack) |
DC-ME-Y413-LX | Digi Connect ME 9210 w/16MB SDRAM, 8 MB Flash, for Digi Embedded Linux, Single Pack |
MODULES FOR NET+OS | |
DC-ME-Y401-C | Digi Connect ME 9210 w/2 MB Flash, 8 MB RAM (single-unit pack) |
DC-ME-Y402-C | Digi Connect ME 9210 w/4 MB Flash, 8 MB RAM (single-unit pack) |
Customers were also interested in
-
Digi Connect ME® 9210 series
- Ultra-compact embedded system-on-modules
- 10/100 Ethernet interface
- RJ-45 form factor
- Compatible with Digi Connect Wi-ME®
- Supports Digi Embedded Linux and NET+OS